Badger-meter ORION Classic (CE) Manuel d'utilisateur

ORION® Water EndpointsORI-UM-00025-EN-06 (June 2014)Installation Manual

ORION® Water EndpointsORION FIXED NETWORK AND MIGRATABLE ENDPOINTS This section contains information regarding identification and encoder compatibilit

Installation ManualActivating the EndpointORION Fixed Network and Migratable endpoints are shipped in an inactive, non-transmitting state known as “Pa

ORION® Water EndpointsORION CLASSIC ENDPOINTSThis section contains information regarding identification and encoder compatibility for field wiring and

Installation ManualActivating the EndpointORION Classic water endpoints are shipped in an inactive, non-transmitting state known as “Pause” mode. The

ORION® Water EndpointsUSING GEL CAPS TO CONNECT AN ENCODER For those connections that are not factory wired or equipped with in-line connectors, follo

Installation ManualFigure 3: Wires in gel cap• Using a crimping tool such as the Badger Meter Parallel Pliers (59983-001), place the gel cap with th

ORION® Water EndpointsENDPOINT INSTALLATION KITS The following kits are available for pit, vault and remote endpoint installations. Instructions for u

Installation ManualPIT INSTALLATIONThrough-the-Lid Installation KitThe Through the Lid Installation Kit (64394-001) is designed for use with a pit lid

ORION® Water EndpointsBelow-the-Lid with Knuckles Installation KitFor below the lid installations, a special Below-the-Lid with Knuckles Installation

Installation ManualIntegrated Pit Lid Hanger Installation KitORION endpoints can be installed below composite and plastic lids that have an integrated

ORION® Water EndpointsPage ii June 2014

ORION® Water EndpointsREMOTE INSTALLATIONRemote Wall Mount Box EnclosureThe ORION Remote Wall Mount Box Enclosure Kit (66009-004) can be used for remo

Installation ManualFigure 13: Remote box enclosure mounting2. Place the endpoint into the ORION remote box enclosure as shown in Figure 14. Make cer

ORION® Water Endpoints4. After the endpoint is mounted in the remote box enclosure, loop the endpoint wire through the strain relief tab and through

Installation ManualIR Programming Bracket (Optional)To hold the IR programming head in place while performing IR functions on ORION endpoints, an opti

ORION® Water Endpoints2. Slide the bracket into the adapter rails at the bottom of the enclosure.Figure 18: IR programming bracket inserted into th

Installation ManualRemote Installation Bracket KitThe Remote Installation Bracket Kit (64394-029) can be used to properly install an ORION endpoint in

ORION® Water Endpoints2. Locate the small triangle aligned with the small hole on the bottom of the installation bracket. This triangle is used to pr

Installation Manual4. With the installation bracket in one hand and the housing in your other hand, hold the bracket still and twist the housing appr

ORION® Water EndpointsINTEGRAL ENDPOINT INSTALLATIONORION Fixed Network, Migratable and Classic endpoints are available in an integral configuration,

Installation ManualRemoving an Integral Endpoint from the Assembly HousingMPORTANTI Removing the endpoint from the assembly housing can only be don

Installation ManualCONTENTSOVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ORION® Water Endpoints3. Rotate the endpoint counter-clockwise 1/4 turn and pull the endpoint and endpoint wire out from the assembly base. Figure 30

Installation ManualINTENTIONAL BLANK PAGEPage 31 June 2014

Making Water Visible®www.badgermeter.comADE, Making Water Visible, ORION and RTR are registered trademarks of Badger Meter, Inc. Other trademarks appe

ORION® Water EndpointsREMOTE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Remo

Installation ManualOVERVIEWThis manual contains installation instructions for ORION® water endpoints.• Installation of ORION endpoints must comply wi

ORION® Water EndpointsIDENTIFICATIONThe ORION endpoint is a three-wire metering endpoint device that requires connection to an encoder to complete the

Installation ManualENDPOINT INSTALLATION GUIDELINESORION endpoints can be installed indoors or outdoors, observing these guidelines:• When a meter is

ORION® Water Endpoints308/Nicor In-line ConnectorsAn in-line connector is an optional feature that allows connectivity to AMR/AMI devices without the

Installation ManualORION CELLULAR ENDPOINTSThis section contains information regarding identification and encoder compatibility for field wiring and a